Wall and hanging kits
Our wall and hanging kits make it easier to mount snap poster frames where they need to be seen. Choose screw-fixed, adhesive or cable-hung options to suit the surface, the frame size and how often the poster will be changed.
What wall and hanging kits are
Wall and hanging kits are the parts used to fix a snap poster frame to a wall, window area or suspended display point. They are supplied for common indoor display jobs where the frame needs to sit straight, open from the front and stay easy to access for poster changes.
For most sites we match the kit to the frame size and the surface. A small A4 or A3 frame in a passage or study can often use a lighter fixing method, while larger A2, A1 and A0 frames normally need a more secure fixing point. In busy offices, schools and clinics we usually suggest a solid mounted option rather than a light temporary one.
- Screw fixing kits for masonry, drywall, timber and other firm surfaces.
- Adhesive fixing kits for smooth, clean indoor surfaces where drilling is not suitable.
- Cable hanging kits for suspended window displays, double-sided frames and feature areas.
- Fixing packs supplied to suit wall-mounted frames and selected hanging layouts.
Sizes, options and working limits
We supply kits to suit snap poster frames from A4 up to A0, as well as custom sizes where the frame profile and weight are known. The right choice depends on both size and location. A frame that works well on a quiet painted passage wall may not be the right choice near a slammed door, an entrance exposed to coastal humidity or a school corridor where people brush past it all day.
Screw-fixed mounting is the most dependable option for medium to large frames and for public-facing indoor areas. Adhesive options suit smaller frames on very smooth surfaces, but they are not a substitute for proper anchors on heavier sizes. Cable kits are useful where wall drilling is not wanted, or where the display must hang in front of glazing, however they need a safe top fixing point and enough clearance below.
- A4 and A3: suitable for screw or selected adhesive mounting indoors.
- A2: generally best on screw fixings, adhesive only on ideal smooth surfaces and lighter frame setups.
- A1 and A0: normally screw-fixed or cable-hung from a proper rated support point.
- Custom sizes: assessed by overall dimensions, frame profile, poster weight and site conditions.
- Double-sided hanging frames: suited to cable systems where viewing from both sides matters.
Adhesive kits do not suit rough plaster, flaky paint, dusty brick, textured wall coatings or damp surfaces. Cable kits do not suit weak ceiling boards without proper anchors. If load-shedding leaves some areas poorly lit, a suspended frame may also cast a shadow so placement matters.
Where these kits suit best
Wall and hanging kits are commonly used in reception areas, passages, staff notice points, waiting rooms, classrooms, home studies, kids rooms, retail aisles and clinic information spaces. They work well when the poster must be updated without taking the whole frame down. Front-opening clip edges make that practical for menus, notices, rota sheets, promotions and school communication.
In Pinetown and the Durban area we often see displays placed in buildings with humidity, afternoon sun and a fair amount of foot traffic. For those conditions, stable mounting and the right cover matter more than trying to keep the fixing hidden at all costs. A neat visible fixing done properly is better than a frame that shifts or lifts at one corner.
- Homes: chore charts, study timetables, artwork swaps and family notice points.
- Offices: reception notices, meeting room schedules, safety communication and HR boards.
- Schools: classroom notices, corridor information and admin office displays.
- Shops and clinics: promotional posters, opening information and queue guidance.
Where they do not suit
These kits are not the answer for every site. If a wall is crumbling, water-damaged or covered in loose paint, the surface should be sorted out first. If the poster must stand free in the middle of a room or mall passage then a freestanding poster stand is usually the better route. If the display area is fully exposed to weather, use an outdoor-rated frame and suitable fixings rather than a standard indoor setup.
We also do not suggest adhesive mounting where cleaning staff regularly wash down the wall, where heat builds up against glass, or where children may pull at the lower corners. Cable hanging is not ideal in low ceilings where people can bump the frame, and not every landlord or body corporate allows ceiling anchors or glazing-related fittings, so please check site rules first.
Installation and site requirements
Good mounting starts with the surface and the measurements. The wall or fixing point must be level, clean and able to carry the frame without movement. For masonry, the correct plugs and screws matter. For drywall, there must be proper anchors or a timber or steel point behind the board. For cable systems, we need to know what the top fixing will be attached to and the drop height available.
Please allow enough clearance for the clip edges to open from the front. This is often missed when a frame is placed too close to shelving, glazing bars, light fittings or a side wall. On hanging displays, leave enough gap below so the frame does not swing into furniture or glass when someone walks past. In humid coastal areas it helps to avoid placing a frame where condensation forms in the early morning.
- Tell us the frame size and whether it is single-sided or double-sided.
- Tell us the wall or support type: brick, concrete, drywall, timber, glass-adjacent or ceiling suspension.
- Tell us if drilling is allowed on site.
- Tell us if the area is air-conditioned, humid, sunny or near an entrance.
- Tell us the finished mounting height and whether children or the public can reach it.
Care and what to include in your enquiry
Once fitted, these kits need very little attention beyond occasional checking that everything remains level and snug. Clean the frame cover with a soft cloth and a mild non-abrasive cleaner. Do not soak the edges or spray cleaner directly into the frame. For adhesive-mounted frames, avoid tugging the bottom edge when opening the poster face. For cable setups, check that the frame still hangs square after poster changes because uneven loading can twist it a bit.
When you enquire through our contact page, include the frame size, quantity, mounting method you prefer if known, and a short note on the site. A quick photo of the wall or hanging area helps, especially for custom sizes or cable-hung displays. If you are not sure what will work, we can guide you on a practical option that suits the location and how often the poster changes.
What our Snap Poster Frames customers say
Verified Google reviews
Questions we get asked
Can I use adhesive kits for any snap frame size?
Not for every size. Adhesive options are best on smaller frames and only on smooth, clean indoor surfaces. Larger frames usually need screw fixings or a properly supported cable system.
Do cable hanging kits work in front of windows?
Yes, they are often used there, especially for double-sided displays. We need to know the drop height, the top fixing point and whether the frame may move in wind from open doors or air-conditioning.
What should I send when asking for the right kit?
Send the frame size, where it will be used, the wall or ceiling type, whether drilling is allowed and if the area is humid, sunny or high traffic. A site photo helps a lot.
Also worth a look
Tell us about the job
Send sizes, materials and where you are through our contact form, and we will come back with the practical options.
Open the contact form